Return to Home





       View DVDs Shopping Cart
Home Page

How to Lay Tile - Do it Yourself!
: Home > "How-to" Help > How to Lay Tile :

HOW TO LAY TILE

Installing your tile floor (tips)

The first thing you will need to lay tile
... is the right tools:


  1. Tape measure, square and caulk line. Hammer, tile nippers, level, and a pry bar.
  2. Wet tile saw and or 4inch die grinder with dry cut diamond blade.
  3. 1/4 inch notched trowel (1/2 inch trowel is recommended for 16x16 or larger tile/stone).
  4. Safety goggles, power cords and any other safety equipment. Don't forget protection for your hands especially when grouting-latex gloves work great!
  5. Rubber grout float, buckets and sponges.


Material List

  1. Cement backer board.
  2. Glue for cement board as wells as galvanized 2 inch roofing nails or backer board screws.
  3. Modified thinset mortar, spacers and grout.
  4. Choose yourself a good tile. Ceramic, porcelain or a natural stone. Note: Buy a good quality tile. Stay away from the red based clay tile. The finish isn't as good and they may break easier. You usually pay for what you get. You can never go wrong with a porcelain tile, although they will be more difficult to cut.


Getting Started

Now its time to start the work by removing the old flooring. If you are building a new home and do not have old flooring or your existing floor is a level cement floor you can go right to the setting your tile step.

The old flooring must be removed for the following reasons:
  • Multiple layers of old flooring will make your finished product to tall.
  • Multiple layers will cause tiles to break and grout to crack.
  • Particleboard sub floors become spongy when wet and can be a breading ground for bacteria.
  • Do your floor right the first time and avoid having to start over.
To have a professional look to your finished project you must remove the baseboards. To begin removing the old sub floor set your skill saw blade to match the depth of the old flooring. Make random cuts in the floor and pry the old floor up with your pry bar. Upon removal of the old sub floor remove any protruding nails or other objects, also make sure the original plywood is screwed tight to the floor joists and not making any squeaking noises when you walk across it. If you discover any loose areas screw it down and clean the work area.

With a clean work area it is now time to set the cement board in place. To add strength to the floor overlap the seams of the plywood with the cement board. The edges of the cement board should break in line with the joists. Use construction grade glue to adhere the cement board to the plywood. Then with 2 inch galvanized roofing nails nail through the cement board and into the floor joist (cement board screws work as well). While nailing the cement board down the spacing should be approximately 8 inches apart. With the cement board in place use a fiberglass mesh tape and a thinset mortar, tape up all your seams


Setting Your Tile

To get started you will need to divide the room horizontally and vertically, make sure you end up with the same size of tile breaking on either side of the room both horizontally and vertically. You will want to pre lay out your tile to get a visual of the finished breaking lines. Once you have completed this choose the longest a straightest wall and chalk a line a line both vertically and horizontally including the breaking lines against the walls. (When using a random square pattern it will not matter where you begin, it only matters that your start with your tile square to the wall) When mixing the thinset bring it to a creamy peanut butter consistency, then with your notched trowel spread the thinset evenly on the floor and begin setting your tiles. Push down firmly on the tile and make sure you are using your spacers for consistent spacing between tiles. Give your tile 24 hours to set before grouting.

Grouting Your Tile

With your tile floor set, now its time to grout. Make sure your floor is clean, scrape away and excess thinset and remove the spacers. Make sure the grout has at least a inch of space to sink down into the joint, if not scrap away the excess thinset. For tile joints between 1/8 inch to inch make sure you use a sanded grout. For tile joints less than 1/8 of an inch use non sanded grout. Mix the grout to a peanut butter consistency, let it slake for a few minuets. Using a rubber float begin spreading into the joints. After 30 minutes to 40 minutes of drying time has occurred, begin to clean off your tiles with a sponge. You must smooth out the joints, but don't wipe too much as it is important to keep the grout as close to the top of the surface of the tile. A few hours later with a terry cloth you may remove any excess haze or dust. You may also mop or sponge it clean the next day using only water.

Sealing Your Grout

When your grout job is complete it is a good idea to seal your grout (or natural stone).The grout must have cured for at least 72 hours. To apply the sealer use a grout applicator you can get at the home store or tile store. (A bottle with a inch brush or roller.) Remove any drips on your tile with a rag. The sealer we recommend is 511 porus plus. It is excellent for sealing grout and any natural stone. (Miracle Sealants Company).

This is a brief caption of the video's instructions on paper. If you are like me, a visual learner you will enjoy following these instructions on DVD. The instructions will make more sense and it's hard to follow directions in a book or pamplet. It is my goal to make things professional and easy by doing things the right way. Anyone can accomplish something if they have been shown the steps to follow.






Purchase our Tile the Right Way Video (DVD)
This 45 minute video is the tool to give you the knowledge and confidence necessary to complete the tile job of your dreams.

List Price: $19.95
Your Price: $15.95
You Save: $4.00 (20%)

Flat Rate Shipping: $4.99

Item Handling Cost: $0.00

Watch Short Video Clips of our Construction Videos




ConstructionVideos.com. All Rights Reserved. 2004. | Website designed by ZurRock
: shop : products : contact us : "how to" help : privacy policy : refund policy : related sites : Construction Videos home :
Visit our friends: Partners